The listed measurements are for general reference only. Please contact Elite Screens to verify product design and dimensions before attempting to integrate its products with any structural or furniture modification. Although a manufacturer may offer product advice, it may be taken or disregarded at the integrator’s discretion. Elite Screens will not be held responsible or be otherwise liable for faulty installations.
Q: I am looking at purchasing an Elite Motorized Screen,VMAX120UWH2. I konw all Elite motorized come with standard 12V trigger built-in, but my projector does not have a trigger out on it. Can I use Universal Wireless 5-12V Projector Trigger | ZU12V ? A: Yes. This device goes between the projector and plug. It is designed for projector w/o low voltage trigger port to work with Elite Screen motorized screen.
Q:I know that all Elite Screens motorized screens include a built-in 5-12 volt trigger RJ45 input port, but what if my projector does not have a 5-12 volt trigger ouput port. How can I take advantage of the automatic down/stop synchronizcation of my Elite motorized screen and my projector? A:Elite Screens offers a wireless Universal 5-12 volt projector accessory (Part# ZU12V) for projectors that do not have a trigger output. Contact your preferred Elite Screens reseller or visit shop.elitescreens.com for information about purchasing this product.
Q: How can I extend my RJ-45 accessory such as my 5-12 v trigger, 3-way wall switch, and IR "eye" sensor? A: You can extend the length of your cable using the ZSP-12V-50B. This 50 feet RJ-45 cable includes an extender plug coupler to allow you to join connections to your existing accessory.
Q: What preventative maintenance does Elite Screens recommend for electric screens? A: Elite strongly recommends using either a standard surge protector or a power conditioner on all electric projection screens.
Q: Does the VMAX 2 have a 5-12 volt trigger input? A: Yes, the VMAX 2 has a RJ-45 5-12 volt trigger input.
Q: How do I know if my projector is compatible with the 5-12 volt trigger? A: Check your projector's manual to see if your projector has a 5-12 volt trigger output. If it does then your projector has the ability to synchronize with your VMAX 2.
Q: Does the VMAX 2 include a 5-12 volt trigger cable? A: Yes, the VMAX 2 includes an RJ-45 5-12 volt trigger.
Q: How can i clean the MaxWhite (matte white) material on the Spectrum screen A: The screen material can be cleaned with mild soap and water
Q: What is the viewing angle on the MaxWhite material? A: The viewing angle of the MaxWhite material is 160°
Q: Will I void my warranty if I cut the power cord cable to hardwire my electric screen? A: No, Elite Screens understand the need to hardwire your electric screen and therefore will not void your warranty.
Q: Where can i find the IR codes for my VMAX2 IR remote? A: Elite provides binary codes for the IR remote, see below.
Q: Are Elite Screens compatible with Harmony Remotes?
A: Yes, Elite's electric screen products are compatible with Harmony remotes and in their database. Please visit the Harmony website for further assistance with programming your remote with our electric screens.
Q: What is the frequency of your RF remote? A: The frequency of the RF remote is 433MHz
Q: Can I increase the Top Black Border on my screen? A: No, your screen’s Top Black border has been set to deploy to its full extent. Attempting to increase will damage the motor and void your warranty with Elite Screens.
Q: How do you decode model #'s? A: Each Elite Screens' model number starts with the product series name. Follow by case color (if applicable, certain models only available in one color), screen material, screen aspect ratio and product series version. Lastly, extra black drop and its length (if applicable). Here is an example.
VMAX 128 U W X 2 -E20
128: 128" Diag. U: Black Case (X: White Case) W: MaxWhite Screen Material X: 16:10 format (V: 4:3 / H 16:9 / S: 1:1 ) 2: Version 2 -E20: Extra Black Drop 20"