FAQ´s
Q: If I install a Spectrum Motorized Screen into the ceiling, what are my possible methods of controlling it? A: Since the Spectrum’s Infrared (IR) Sensor is hidden within the ceiling, there are a few options in which to control a ceiling installed Spectrum Screen:
- IR Eye Extender (ZSP-EYE&12V): With the need of line of sight, the IR signal will not be sensed by the IR receiver built within the housing of the Spectrum. By using an IR eye extender that attaches via the Spectrums all purpose RJ45 port, the extended sensor provides a solution to this problem.
- Radio Frequency (RF) Remote (ZSP-RF-B, ZSP-RF-W): The Spectrum, unfortunately, does not come with an RF remote. It does, however, have an RF receiver built into the housing. Without the need of direct line of sight, an RF remote would be a good control option.
- In-Wall Switch (ZIW-B, ZIW-W, ZIW-W1): The spectrum comes with an all purpose RJ45 port. By routing a cable within the wall, the In-Wall Switch provides a close proximity control option. In addition, you can create your own in-wall switch by purchasing only our ZIW-Module.
- Wireless 12V Trigger (ZSP-TR01): Use your projector as a screen control option by hooking up this simple device to your projector’s output trigger port. If your screen doesn’t have an output trigger port, the Universal Wireless 12V Projector Trigger (ZU12V) works just as well for all projectors.
Q: I know that all Elite Screens motorized screens include a built-in 5-12 volt trigger RJ45 input port, but what if my projector does not have a 5-12 volt trigger ouput port. How can I take advantage of the automatic down/stop synchronizcation of my Elite motorized screen and my projector?
A: Elite Screens offers a wireless Universal 5-12 volt projector accessory (Part# ZU12V) for projectors that do not have a trigger output. Contact your preferred Elite Screens reseller or visit shop.elitescreens.com for information about purchasing this product.
Q: How can I extend my RJ-45 accessory such as my 5-12 v trigger, 3-way wall switch, and IR "eye" sensor?
A: You can extend the length of your cable using the ZSP-12V-50B. This 50 feet RJ-45 cable includes an extender plug coupler to allow you to join connections to your existing accessory.
Q: What preventative maintenance does Elite Screens recommend for electric screens?
A: Elite strongly recommends using either a standard surge protector or a power conditioner on all electric projection screens.
Q: How can i clean the MaxWhite (matte white) material on the Spectrum screen?
A: The screen material can be cleaned with mild soap and water.
Q: What is the viewing angle on the MaxWhite material?
A: The viewing angle of the MaxWhite material is 160°.
Q: Does the Spectrum have a 5-12 volt trigger input?
A: Yes, the Spectrum has a RJ-45 5-12 volt trigger input.
Q: How do I know if my projector is compatible with the 5-12 volt trigger?
A: Check your projector's manual to see if your projector has a 5-12 volt trigger output. If it does then your projector has the ability to synchronize with your Spectrum.
Q: Does the Spectrum include a 5-12 volt trigger cable?
A: Yes, the Spectrum includes an RJ-45 5-12 volt trigger cable.
Q: Will I void my warranty if I cut the power cord cable to hardwire my electric screen?
A: No, Elite Screens understand the need to hardwire your electric screen and therefore will not void your warranty.
Q: Where can i find the IR codes for my Spectrum IR remote?
A: Elite provides binary codes for the IR remote, see below.
Up: 1111 0000 0001
Stop: 1111 0000 0010
Down: 1111 0000 0100
Q: Are Elite Screens compatible with Harmony Remotes?
A: Yes, Elite's electric screen products are compatible with Harmony remotes and in their database.
Please visit the Harmony website for further assistance with programming your remote with our electric screens.
http://myremotesetup.com/easyzapper/New/Main.asp
Q: Can I increase the Top Black Border on my screen?
A: No, your screen’s Top Black border has been set to deploy to its full extent. Attempting to increase will damage the motor and void your warranty with Elite Screens.
Q: How do you decode model #'s?
A: Each Elite Screens' model number starts with the product series name. Follow by case color (if applicable, certain models only available in one color), screen material, screen aspect ratio and product series version. Lastly, extra black drop and its length (if applicable). Here is an example.
ELECTRIC 128 X
Electric: Spectrum Series
128: 128” Diag.
X: 16:10 Format
